Arduino board
If you like experimenting with different electronic components but don’t have sufficient know-how, then Arduino is what you need to make a start…
So what is Arduino?
Arduino is a microcontroller-based open source electronic prototyping board which can be programmed with an easy-to-use Arduino IDE.
In this article, I will talk about what’s on the Arduino UNO board and what it can do. UNO is not the only board in the Arduino family. There are other boards like Arduino Lilypad, Arduino Mini, Arduino Mega, and Arduino Nano. However, the Arduino UNO board became more popular than other boards in the family because it has documentation that is much more detailed. This led to its increased adoption for electronic prototyping, creating a vast community of electronic geeks and hobbyists.
In recent times, the UNO board has become synonymous with Arduino.
The major components of Arduino UNO board are as follows:
Now let’s take a closer look at each component.
USB connector:
This is a printer USB port used to load a program from the Arduino IDE onto the Arduino board. The board can also be powered through this port.
Power port:
The Arduino board can be powered through an AC-to-DC adapter or a battery. The power source can be connected by plugging in a 2.1mm center-positive plug into the power jack of the board.
The Arduino UNO board operates at a voltage of 5 volts, but it can withstand a maximum voltage of 20 volts. If the board is supplied with a higher voltage, there is a voltage regulator (it sits between the power port and USB connector) that protects the board from burning out.
Microcontroller:
It is the most prominent black rectangular chip with 28 pins. Think of it as the brains of your Arduino. The microcontroller used on the UNO board is Atmega328P by Atmel ( a major microcontroller manufacturer). Atmega328P has the following components in it:
Atmega328P is pre-programmed with bootloader. This allows you to directly upload a new Arduino program into the device, without using any external hardware programmer, making the Arduino UNO board easy to use.
Would you like to get updates once a month on our latest articles? We won’t spam, we promise. Subscribe now to The HackerEarth Blog!
Analog input pins:
The Arduino UNO board has 6 analog input pins, labeled “Analog 0 to 5.” These pins can read the signal from an analog sensor like a temperature sensor and convert it into a digital value so that the system understands. These pins just measure voltage and not the current because they have very high internal resistance. Hence, only a small amount of current flows through these pins.
Although these pins are labeled analog and are analog input by default, these pins can also be used for digital input or output.
Digital pins:
You can find these pins labeled “Digital 0 to 13.” These pins can be used as either input or output pins. When used as output, these pins act as a power supply source for the components connected to them. When used as input pins, they read the signals from the component connected to them.
When digital pins are used as output pins, they supply 40 milliamps of current at 5 volts, which is more than enough to light an LED.
Some of the digital pins are labeled with tilde (~) symbol next to the pin numbers (pin numbers 3, 5, 6, 9, 10, and 11). These pins act as normal digital pins but can also be used for Pulse-Width Modulation (PWM), which simulates analog output like fading an LED in and out.
Reset switch:
When this switch is clicked, it sends a logical pulse to the reset pin of the Microcontroller, and now runs the program again from the start. This can be very useful if your code doesn’t repeat, but you want to test it multiple times.
Crystal oscillator:
This is a quartz crystal oscillator which ticks 16 million times a second. On each tick, the microcontroller performs one operation, for example, addition, subtraction, etc.
USB interface chip:
Think of this as a signal translator. It converts signals in the USB level to a level that an Arduino UNO board understands.
TX – RX LEDs:
TX stands for transmit, and RX for receive. These are indicator LEDs which blink whenever the UNO board is transmitting or receiving data.
Now that you have explored the Arduino UNO board, you have started your journey toward building your first IoT prototype. In the next article, we will discuss Arduino programming and do a few experiments with Arduino and LEDs.
Looking to make your hiring process more effective and less biased? An interview scorecard might…
The Progressive Pre-Employment Assessment is a crucial step in the hiring process, as it evaluates…
Recruiters constantly look for innovative ways and solutions to efficiently attract and engage top talent. One…
At HackerEarth, we take pride in building robust proctoring features for our tech assessments. The…
Imagine a world where you can easily find candidates with the exact skills and experience…
Recruitment platforms play a critical role during recruitment. These platforms offer a suite of tools…