In the previous article, we studied the basic structure of Arduino programming with examples. Now, in this article let’s look at a few more Arduino programming concepts like the following:
if statement
The “if” statement is a conditional statement, it checks if a certain condition is met. If yes, it executes the set of statements enclosed in curly braces. If the condition is false, then the set of statements will skip the execution.
The syntax of the “if” statement is follows:
if(some variable ?? state)
{
statement-1;
.
.
.
statement-n;
}
In the above format, ?? represents comparison operator
X==Y // Check if X is equal to Y
X!=Y // X is not equal to Y
X<Y // Check if X is less than Y
X>Y // Check if X is greater than Y
X<=Y // Check if X is less than or equal to Y
X >=Y // Check if X is greater than or equal to Y
Note: “=” is used to assign a value, where as == is used for comparison.
Example
if (LED == HIGH)
{
digitalWrite(LED, LOW);
}
if-else statement
This statement makes an “either-or decision. The if statements checks a condition. If it is true, it executes a set of statements; if the condition is not true, it executes other set of statements.
The syntax of “if-else” statement is as follows:
if (some variable ?? state)
{
statement-1;
.
.
.
statement-n;
}
else
{
statement-1;
.
.
.
statement-n;
}
Example
if(LED==High)
{
digitalWrite(LED, LOW);
}
else
{
digitalWrite(LED,HIGH);
}
else can also be preceded by another if statement; the syntax is as follows:
if (some variable ?? state)
{
statement-1;
.
.
.
statement-n;
}
else if ( some variable ?? state )
{
statement-1;
.
.
.
statement-n;
}
else
{
statement-1;
.
.
.
statement-n;
}
The if-else state is used when you want to run two mutually exclusive tests and run a separate set of statements for each test.
for loop
If you want to repeatedly execute a set of statements for a specific number of times, then you can use a for loop.
The syntax of the “for” statement is as follows:
for(initialization; condition; expression)
{
Statement-1;
.
.
.
Statement-n;
}
In the for loop, the variable initialization is done only once. After this the set of statements is executed, the initialization step is skipped and directly the condition will be checked. If the result is true, before executing the set of statements in the curly braces, the expression will be executed.
Example
for (int X=0; X<50; X++) //Variable X is initialized to 0, check if X is less than 50, if yes, increase the value of X by 1
{
digitalWrite (12, HIGH); //Turn on the component connected to pin number 12
delay(1000); //Wait for 1 sec
digitalWrite ( 12, LOW); //Turn OFF the component connected to pin number 12
delay (1000); //Wait for 1sec
}
Note: X++ is same as X=X+1 or X+=1
while loop
The while loop executes a set of statements until the expression inside the parentheses is false.
The syntax of the “‘while” loop is as follows:
while (some variable ?? value)
{
Statement-1
.
.
.
Statement-n;
}
Example
while(i<=200)
{
digitalWrite (12, HIGH); //Turn on the component connected to pin number 12
delay(1000); //Wait for 1 sec
digitalWrite ( 12, LOW); //Turn OFF the component connected to pin number 12
delay (1000); //Wait for 1sec
i++;
}
The set of statements under a while loop is executed only if the condition is true. In the while loop, there should be a statement which changes the state of the tested variable. If not, the while loop will never exit. In the example above, the tested variable is “i” and the statement that changes its state is “i++.”
do while loop
If you want to execute a set of statements once and repeatedly execute the set if a certain condition is true,the syntax of the “do-while” loop is as follows:
do
{
statement-1;
.
.
.
statement-n;
} while (some variable ?? value);
The do-while loop is a bottom-driven loop because the condition is checked at the end, after executing the set of statements at least once.
Example
do
{
temperature=readSensor( ); // Variable temperature is set to boiler temperature
digitalWrite(13, HIGH); //Turn ON the LED connect to pin number 13
delay(1000); //Wait for 1sec
}while(temperature<=35); // Check if temperature is less than or equal to 35
The program above turns on the LED if the boiler temperature is less than or equal to 35.
pinMode
This statement is used in the preparation block of the Arduino program, that is, in the void setup() function.The pinMode statement is used to configure a pin to behave in either the INPUT mode or OUTPUT mode.
The syntax of the “pinMode” statement is as follows:
pinMode (pin-number, behaviour);
Example
pinMode (13, OUTPUT);
Note: Digital pins on the Arduino board are input, by default, so these pins can be used in the INPUT mode even without declaration.
digitalRead
This statement reads the state of the specified digital pin and the result will be either HIGH or LOW.
The syntax is as follows:
state=digitalRead(pin-number);
digitalWrite
digitalWrite statement is used to either turn ON or OFF the device connected to a specified digital pin.
The syntax of the “digitalWrite” statement is as follows:
digitalWrite(pin-number, status)
Example
digitalWrite(12,HIGH);
digitalWrite(13,LOW);
analogRead
This statement reads the value from the specified analog pin on the Arduino board with 10-bit resolution. The result will be an integer value in the range of 0 to 1023.
The syntax of the “analogRead statement” is as follows:
value=analogRead (pin-number);
analogWrite
This statement writes a pseudo-analog value to the specified pin. The value is called pseudo-analog because it is generated by Pulse Width Modulation pins (PMW) on the Arduino board. The value can be specified as a variable or constant in the range of 0 to 255.
The syntax of “analogWrite” statement is as follows:
analogWrite(pin-number, value);
Example
analogWrite(9,255);
Note: Analog pins need not be declared as INPUT or OUTPUT pin.
Congratulations! You have completed the basic level of Arduino programming, but do not settle down as there are a few more things to learn before you become a pro.
In the next article, we will discuss how you can work with different sensors. Till then keep building.
Organizations of all industries struggle with employee turnover. The high turnover rates cause increased hiring…
Virtual hiring events are becoming vital for modern recruitment, and the hiring world is changing…
The competition for talent today is intense, and this makes it very important for organizations…
Hiring trends are continuously evolving over the ages to keep pace with the latest technological…
Hiring practices have changed significantly over the past 30 years. Technological advancements and changing workforce…
In the current world, where the hiring process is ever-evolving, it has become crucial to…